Overview
Use the printer's control panel to configure your Wi-Fi network and security settings on the printer and allow it to join the wireless network..
As users move to faster networks, the need for wireless clients supporting 5GHz frequencies using 40MHz channel width becomes more prevalent. Lexmark has added this compatibility for a number of printers.
Before you begin
Check for the presence of 802.11 a/n under Menus (Settings) > Network/Ports > Network 1 > Network 1 Setup > Wireless > Compatibility. Click here for an illustration
If you do not see a/b/g/n or a/n modes, then you will need to update your printer's firmware to EC6; i.e., LW63.##.P638, or later.
Other configuration methods available
- Consider configuring wireless settings from the printer's IP address, if any of the following conditions apply:
- Your printer is connected to a wired network.
- The printer lacks a touch screen.
- Your installation software is not available.
- You do not have a local PC or USB cable.
- Consider the following options if you are using any of the following:
- Personal Identification Number (PIN) or Push Button Configuration (PBC
- Initiate WPS from router's configuration web page, a button on the wireless router/AP, or printer’s PIN or PBC menu option (See Step 7 below).
Note: PBC requires turning on WPS Autodetection, found under
Please reference your router's documentation or router's technical support services to find out more about this capability.
- Bonjour* configuration on Apple Macintosh or AirPrint of your printer supports it.
* Requires mDNS and DDNS to be enabled on the printer under Settings > Network/Ports > TCP/IP.
Configuring wireless settings from the control panel
Before proceeding to the steps below, you may want to review these tips:
- Know your network's wireless compatibility mode: 802.11 a/b/g/n.
- Know your compatibility mode's channel width: 20MHz, 40MHz, 20/40MHz.
- Know your wireless network name (SSID), passphrase, security mode and encryption type.
- Power-cycle (ON-OFF-ON) the printer with network cable detached in order to see Network 1. See Selecting Active Network Card if Network 1 never appears as a menu option; and again, verify the network cable is detached from the printer. The Active Network Card should be set "Auto" without Ethernet cable or "Network Card 1".
- If manually entering SSID and encryption values, it is crucial they be identical to those found on your router's AP.
Solution
Press Menu or Home. Depending on the printer model, the icon’s buttons may appear as a Wrench, a List, or a House. Click here for an illustration.
Proceed to the following menu location: Network/Ports > Network 1 > Network 1 Setup > Wireless > Wireless Connection Setup.
Use the OK button or combo ICON/CHECKMARK to select menu options or submit values.
ARROW buttons, regardless of device model, will scroll down menu lists.
Check the 802.11 compatibility mode settings ‑ click here for an illustration:
- 802.11b / g - 2.4GHz, 20MHz channel width
- 802.11b/ g / n - 2.4GHz, 20/40MHz channel width
- 802.11a / b/ g / n - 2.4 & 5GHz, 20MHz channel width
- 802.11a / n - 5GHz - 40MHz channel width (channel width is automatic if adapter detects 802.11a)
Search for networks to identify all reachable APs ‑ Network Names (SSIDs).
- If Successful:
- Select the correct Network and jump to Step 11 to complete configuration.
- Or, select Other and jump to Step 9 and begin manual configuration as seen here
- If Not successful as seen here:
- Search again.
- Select Enter a network name and perform manual configuration.
Manually configure ALL wireless settings. Proceed to Step 9
Join your network using Push Button or PIN methods. See router's or AP User Guide for instructions and the printer's User Guide for additional assistance.
Enter Network Name (SSID) and then press OK or the Checkmark as seen here.
Select Network Mode (Infrastructure or Ad hoc). Click here for an illustration.
Select Wireless Security Mode (Disabled, WEP, WPA‑PSK, WPA2‑PSK) as seen here.
Select Encryption Type (Cipher). Click here for an illustration of the options ‑ Auto, TKIP, AES
Enter Passphrase* and then press OK or the Checkmark as seen here.
* Common mistakes include misspelled words and not recognizing spaces, underscores, symbols, or the capitalization of certain letters.
Printer will attempt to connect to the network. Click here for an illustration.
If unsuccessful, locate the Trouble Code, which may help determine the problem. Ethernet 802.11 a/b/g/n Network Setup page
Verify Connection
Look at your Ethernet 802.11a/b/g/n network settings page.
- If the status appears as Not Connected then locate the Trouble Code near the bottom of the page or on the second sheet; i.e., "Can't Find Wireless Network".
- If the status appears as Connected then the printer should be successfully connected to your WLAN. Attempt to print, scan, or observe that you are still able to access the embedded web server.
Forced 'Std. Network' setting prevents wireless configuration
If the Active Network Card is set to the Std. Network, not only will wireless configuration failure occur, but any printer already communicating wirelessly will lose connection since this setting forces a wired Ethernet connection only.
To do this from the printer's web page:
Click Settings.
Click Network/Ports.
Click on Select Active Network Card.
Select required Auto, Network Card 1.
Click Submit.
To do this from the printer control panel:
Turn OFF the printer.
Disconnect the network cable from the printer.
Turn ON the printer.
Press Network/Ports >Active NIC.
Select required Auto or Network Card 1.
Click the check mark.
Observe Submitting changes. MX410 Screenshot
The printer will have to reset or reboot before it can attempt to join the active wireless network.
Note: The printer has to reset because it cannot run concurrent wireless and wired network card options. This allows the printer to detect the newly activated network card option. NIC – Network Interface Card
Active network card behavior
Setting and Selection Behavior | Good to know |
---|---|
Auto (Default) In this mode, the active network card will switch from STD NETWORK to NETWORK CARD 1 automatically, but only if the printer recognizes that the wireless print server has been configured and you have disconnected the network cable. Note: It will show connected on the setup sheet only if the printer can complete client-to-AP authentication and association. |
|
Network Card 1 In this mode, the active network card (MarkNet 8350/8352 wireless adapter) is forced ON. This is evidenced by the presence of a Ethernet 802.11 a/b/g/n page if you print the Network Setup page. You will disable the wired Ethernet 10/100/1000 (Internal network adapter [INA, NIC]). |
|
Std. Network
|
|
Trouble codes and suggestions
Trouble code explanation | Possible cause and corrective actions |
---|---|
Cannot associate with wireless network Signal Quality – (Unacceptable) |
Note: WPA uses TKIP/PSK and WPA2 adds AES. Note: * See router or access point documentation. |
Access point is not using WPA |
|
Signal strength too weak |
Note: The setting page does not list SNR on our network settings sheet, but it may list signal strength, which accounts for overall signal quality. SNR = RF signal power relative to power of noise in the environment; e.g., 43db SNR is better than 37db SNR. |
Can't find wireless network | Possible causes and suggestions include:
|
Signal strength too strong |
|
LEGACY ID: HO3913